Hello,
I would like to osmosis rainwater to supply my aquariums.
Today, I consume around 500 liters of pipe water per 100 liters of RO water produced per day. On average, my reverse osmosis units run 3 hours per day.
I wonder about what type of pump to use to supply these osmosis units for use in rainwater: surface pump or booster group, other? .. I have read a lot about it and the general opinion is that you should use a booster rather, which I have a little trouble understanding for the following reasons ..
If you start on a booster pump with 20 liters tank and factory set to 2 bar when triggered and 3,5 bar when stopped, roughly you need to consume 5/6 liters before the pump starts. however with my reverse osmosis units, I use 5 liters in 2-minute moims. This therefore means that my pump will be triggered every two minutes, which does not seem very suitable for the longevity of the pump and the electrical consumption. (far too many stops and restarts)
Otherwise, can a surface pump operate continuously for 3 hours without worrying? Does the fact that it is clamped at the output with the osmosis units not risk over-stressing the joints?
A booster pump for reverse osmosis, can it be enough knowing that between my recuperator and the reverse osmosis there is only very little distance?
Could an informed connoisseur confirm / deny my figures and orient me?
Goods.
Laurent
What type of pump for osmoser of rainwater?
Hi,
Thank you for this answer .. the booster pump, it is indeed a track that I was considering in particular for the simplicity of implementation and consumption (no diaphragm inflation bp, no pressure switch setting, etc.) .. it was however advised against because it was considered a little too light. I intend to put 4 prefilters (5µ, carbon 5µ, 5µ, 1µ) between the pump and the membranes, the pressure drops will not be- not too important? where to place the prefilters? in suction or discharge of the pump?
I therefore abandon the Booster track which, a priori, is not suitable for continuous use over several hours with an osmosis unit.
Thank you for this answer .. the booster pump, it is indeed a track that I was considering in particular for the simplicity of implementation and consumption (no diaphragm inflation bp, no pressure switch setting, etc.) .. it was however advised against because it was considered a little too light. I intend to put 4 prefilters (5µ, carbon 5µ, 5µ, 1µ) between the pump and the membranes, the pressure drops will not be- not too important? where to place the prefilters? in suction or discharge of the pump?
I therefore abandon the Booster track which, a priori, is not suitable for continuous use over several hours with an osmosis unit.
0 x
Personally, I had put a 25µm prefilter before the pump to protect it, then after the pump a 5µm anti-sediment prefilter and a carbon prefilter (carbon is only there to protect the membrane of the reverse osmosis unit) and for finish the osmosis membrane.
A booster pump is really very powerful so I think that even with 4 prefilters there will be no problem.
A booster pump is really very powerful so I think that even with 4 prefilters there will be no problem.
0 x
Thank you, you help me a lot to find the best solution .. I still have a few questions .. I am told that this kind of pump does not suck and that it is necessary to place the rain water collector mini at 40 cm above the pump so as to create a flow by gravity .. do you confirm? ... or are you lucky enough to have a booster pump that sucks?
0 x
-
- Similar topics
- Replies
- views
- Last message
-
- 1 Replies
- 10470 views
-
Last message by Forhorse
View the latest post
31/07/12, 17:51A subject posted in the forum : Water management, plumbing and sanitation. Pumping, drilling, filtration, wells, recovery ...
-
- 0 Replies
- 7045 views
-
Last message by yop
View the latest post
30/04/10, 18:15A subject posted in the forum : Water management, plumbing and sanitation. Pumping, drilling, filtration, wells, recovery ...
Who is online ?
Users browsing this forum : No registered users and 176 guests