Page 1 on 2

"HATEM" experience following and photos

published: 30/12/07, 18:07
by naca
Well ....

Shooting session this weekend. :D

On the program: modification of the motor shafts, replacement of the bearings in order to be able to add a weight of approximately 2 Kg on each motor to gain in energy cynetique as advocates the patent of Mr Hatem.

Modifying trees (before, after):
Image

Masselotte in place on tray:
Image
Image

Spinning mass:
Image

Difficult to take stock for the moment, I realized that a flyweight, so far, I contaté a lower consumption with the addition of the weight on the generator N ° 1.
next week end : Cry:

Re: "HATEM" experience following and photos

published: 31/12/07, 07:42
by Tagor
naca wrote:, replacement of the bearings in order to be able to add a weight of about 2 Kg on each engine to gain energy cynetique


well yes, it is this kinetic energy which gives this impression of "degravitation"

in fact, the more kinetic energy there is, it runs without friction, but none on observable unity!

Re: "HATEM" experience following and photos

published: 31/12/07, 07:52
by Tagor

that said what a beautiful achievement!
Image

published: 31/12/07, 10:58
by gegyx
Beautiful achievement indeed!
: Shock:
What makes me uneasy is the modification of the axis (before-after).

- It is a sleeve axis that you have nested by the outside on the old one, with a tightening BTR? And so hello finishing, so that the axis rotates centered ...
- It is a sleeve axis that you have nested inside, on the old one, with a tightening BTR, surely until before winding? And then, modifying the bearing, to place a suitable bearing to the new diameter (bearing diameter identical ext and larger inside) ...

published: 31/12/07, 11:21
by Christine
Answer by naca (which was wrong and I copy you here):

To reply to Gegyx

It is a sleeve "fitted" and hot glued, then passed around in order to precisely realign the shaft.
There are no clamping screws.

This type of mounting is indestructible .... (normally) Crying or Very Sad


cordially

published: 31/12/07, 11:28
by naca
We look forward to seeing you!

Where am I?

Additional clarification:

The axis changes from 12 to 20 mm, so the bearing is replaced by a

32 x 20 instead of an 32 x 12.
:?
cordially

published: 01/01/08, 12:48
by quartz
Happy New Year everyone

Beautiful achievement Naca, Well done

A + + +

published: 01/01/08, 16:56
by naca
Well, I think I did not understand everything.

I opened a new topic, I believe, but with the same subject,

Can the moderator put this subject after the other, you know, the one where it all started, the one that has 110 like pages on the same subject.

please :D

published: 02/01/08, 12:21
by Christophe
naca wrote:Can the moderator put this subject after the other, you know, the one where it all started, the one that has 110 like pages on the same subject.

please :D


No I do not prefer, it's better to leave them independent, for your answer error and for others here is the subject to which naca refers: https://www.econologie.com/forums/modificati ... t4539.html

I advise you, naca, to rewrite this answer here.

published: 08/01/08, 19:27
by caracole
Congratulations to Naca Superb Achievement and Quality Photos!

But I would like to know
- Which motor (s) or motor + AC DC generator etc etc ...
I would like to realize something resembling (without redoing an axis because I have no tower or the technical means of Naca which I salute the quality of his work)

Thank you