Hello, as part of a graduation project I had to manufacture a Pantone system and adapt it to a small petrol engine that I recovered. Everything went well during the design, but I have a few questions for experts like you:
[color = red] - The engine runs very well but it does not consume no water. [/ color]
- It is impossible to run the engine until the system is hot. Is this the case for you?
And last question, to understand what is happening in the system, I had to put forward several hypotheses but only retained one. It would be a steam cracking of fuel molecules helped by water.
I already have in mind an experiment to determine whether or not it is the solution if you want I can keep you posted. Let me know.
Goodbye and thank you in advance for your answers.
Problem of water consumption
-
- Econologue expert
- posts: 4075
- Registration: 12/01/07, 08:18
- x 4
Hello scherran,
Your explanations are a bit short.
Example,
A little video, where some pictures of the montages might get the old wolves out of their cave
But on weekends, it's pretty calm.
If your problem is well explained, if your editing is also explicit, you may have answers ...
Your explanations are a bit short.
Example,
?small engine
Running the engine is impossible until the system is warm?
the solution of what?I already have an experiment in mind to determine whether or not this is the solution
A little video, where some pictures of the montages might get the old wolves out of their cave
But on weekends, it's pretty calm.
If your problem is well explained, if your editing is also explicit, you may have answers ...
0 x
Man is by nature a political animal (Aristotle)
Hello,
the experience that I have in mind is to prove the formation of an alkene at the outlet of the reactor which will prove the steam cracking hypothesis and invalidate that of the electrification of water vapor.
However my important problem is that my system does not consume water at all, it is only the essence which evaporates from the bubbler, the water remains.
Here is the engine to which I chose to adapt the system
Here is the system finished and running.
the experience that I have in mind is to prove the formation of an alkene at the outlet of the reactor which will prove the steam cracking hypothesis and invalidate that of the electrification of water vapor.
However my important problem is that my system does not consume water at all, it is only the essence which evaporates from the bubbler, the water remains.
Here is the engine to which I chose to adapt the system
Here is the system finished and running.
0 x
-
- Econologue expert
- posts: 4075
- Registration: 12/01/07, 08:18
- x 4
Now, we're going to take you a little more seriously.
Can you say a little more about your studies? it is also important.
And also what motivates you in this work. (it's just a personal curiosity)
For the rest, I noticed that your "French" is correct
Sms language pollution
Okay, now I hope the pantom pros are going to move a little
0 x
Man is by nature a political animal (Aristotle)
Hello sherran
If you put water and petrol in the same bubbler, it is normal for the lighter fractions of petrol to evaporate first, then the heavier fractions, then water ... Your bubbler is certainly not hot enough for the water. For this to work better, it is better to separate the water bubbler (to be heated around 75 to 95 °) and the gas (bubbler / circuit) below 65 °.
Use the site's search engine, there are lots of different valid solutions for it to work properly.
A+
sherran wrote:the experience that I have in mind is to prove the formation of an alkene at the outlet of the reactor which will prove the steam cracking hypothesis and invalidate that of the electrification of water vapor.
Your experience is interesting, but you would also have to prove that the two phenomena do not coexist ... Can you explain to us how you intend to carry out the manipulation? If at the same time you could give us a detailed diagram of your achievement, it will be great and much easier to try to help you.However my important problem is that my system does not consume water at all, it is only the essence which evaporates from the bubbler, the water remains.
If you put water and petrol in the same bubbler, it is normal for the lighter fractions of petrol to evaporate first, then the heavier fractions, then water ... Your bubbler is certainly not hot enough for the water. For this to work better, it is better to separate the water bubbler (to be heated around 75 to 95 °) and the gas (bubbler / circuit) below 65 °.
Use the site's search engine, there are lots of different valid solutions for it to work properly.
A+
0 x
Reason is the madness of the strongest. The reason for the less strong it is madness.
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
[Eugène Ionesco]
http://www.editions-harmattan.fr/index. ... te&no=4132
-
- Similar topics
- Replies
- views
- Last message
-
- 6 Replies
- 13935 views
-
Last message by jime
View the latest post
06/05/08, 12:26A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 38 Replies
- 34471 views
-
Last message by Christophe
View the latest post
01/01/09, 14:55A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 14 Replies
- 12126 views
-
Last message by Thibounet
View the latest post
03/03/07, 11:44A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 1 Replies
- 6118 views
-
Last message by PITMIX
View the latest post
03/11/05, 22:43A subject posted in the forum : Water injection in heat engines: information and explanations
-
- 2 Replies
- 4060 views
-
Last message by Other
View the latest post
28/09/05, 05:13A subject posted in the forum : Water injection in heat engines: information and explanations
Go back to "Water injection in heat engines: information and explanations"
Who is online ?
Users browsing this forum : No registered users and 81 guests