scoop oil burner with max recycling
-
- Grand Econologue
- posts: 1155
- Registration: 21/06/09, 01:02
- Location: Britain BZH powaaa
- x 2
-
- Grand Econologue
- posts: 1155
- Registration: 21/06/09, 01:02
- Location: Britain BZH powaaa
- x 2
-
- Grand Econologue
- posts: 1155
- Registration: 21/06/09, 01:02
- Location: Britain BZH powaaa
- x 2
Good evening, thank you Alain, I re upload and submit the link and hope it works this time
http://dai.ly/fb815Q
ou
http://www.dailymotion.com/video/xh9urx ... ed&start=9
or even normally there's a trick that should go lol .
Otherwise go to dailymotion directly and look for video 0015 "vegetable oil and vegetaline"
see you
http://dai.ly/fb815Q
ou
http://www.dailymotion.com/video/xh9urx ... ed&start=9
or even normally there's a trick that should go lol .
Otherwise go to dailymotion directly and look for video 0015 "vegetable oil and vegetaline"
see you
0 x
-
- Grand Econologue
- posts: 1155
- Registration: 21/06/09, 01:02
- Location: Britain BZH powaaa
- x 2
Bonjour,
news, photos and video, installation testing continues as the cast began with a bang (Not much I start too fast I break a crucible arff)
I explain zef vote, the flame is a hot spot the crucible fart almost instantly logic Just take the two seconds required to think about arff. So for widening the method of gas statment is necessary;).
This brief being that it gives 20 in minutes, all was dark red cherry at the exit, it's what we call a carcass compression in hard disk alu
Otherwise good few photos of mad max burner and Evolution;).
I have changed the faucet handle by a large washer down in strength is much more precise;).
Have ventillo see the wall gas boiler (recup it seem that no longer functioned lol, a disassembly cleaning remotage with tightening which was more and the zou is distributed ).
So the tuyere made with a bottle of W40 she reddened but hold on.
Also ready
Otherwise farewell tank Lilliputian and live the old canister of déchette;).
So I'll end my piston pump;) and my inter put on hold due to tank too small to put an effective ball.
otherwise I just deleted my video lol (it is not even the trash ) I redo a job and I this is just a delay .
see you later
news, photos and video, installation testing continues as the cast began with a bang (Not much I start too fast I break a crucible arff)
I explain zef vote, the flame is a hot spot the crucible fart almost instantly logic Just take the two seconds required to think about arff. So for widening the method of gas statment is necessary;).
This brief being that it gives 20 in minutes, all was dark red cherry at the exit, it's what we call a carcass compression in hard disk alu
Otherwise good few photos of mad max burner and Evolution;).
I have changed the faucet handle by a large washer down in strength is much more precise;).
Have ventillo see the wall gas boiler (recup it seem that no longer functioned lol, a disassembly cleaning remotage with tightening which was more and the zou is distributed ).
So the tuyere made with a bottle of W40 she reddened but hold on.
Also ready
Otherwise farewell tank Lilliputian and live the old canister of déchette;).
So I'll end my piston pump;) and my inter put on hold due to tank too small to put an effective ball.
otherwise I just deleted my video lol (it is not even the trash ) I redo a job and I this is just a delay .
see you later
0 x
- Capt_Maloche
- Moderator
- posts: 4559
- Registration: 29/07/06, 11:14
- Location: Ile-de-France
- x 42
EH well, sacred assembly
you will have the opportunity to ride it on a forward boiler?
you will have the opportunity to ride it on a forward boiler?
0 x
"Consumption is similar to a search consolation, a way to fill a growing existential void. With, the key, a lot of frustration and a little guilt, increasing the environmental awareness." (Gérard Mermet)
OUCH, OUILLE, OUCH, AAHH! ^ _ ^
OUCH, OUILLE, OUCH, AAHH! ^ _ ^
-
- Grand Econologue
- posts: 1155
- Registration: 21/06/09, 01:02
- Location: Britain BZH powaaa
- x 2
Hello,
This arrangement is the test set, cast and forge, and so learn to actually make a fitting (but another try on the principles of this package).
I'm not finished yet actually this is just the beginning .
I have two little ideas I ettrais me under shortly to test, including one with a HF.
The I have another idea which seem to me better AUQ the scope of its effects for mcontrer pulsar, not the idea is to put the tuyere HF vibration and thus finish spray or fog all the drops that would come to touch the tuyere.
It's about you it's someone ???
see you
This arrangement is the test set, cast and forge, and so learn to actually make a fitting (but another try on the principles of this package).
I'm not finished yet actually this is just the beginning .
I have two little ideas I ettrais me under shortly to test, including one with a HF.
The I have another idea which seem to me better AUQ the scope of its effects for mcontrer pulsar, not the idea is to put the tuyere HF vibration and thus finish spray or fog all the drops that would come to touch the tuyere.
It's about you it's someone ???
see you
0 x
Hello,
lot of work
I remain convinced that the resonance is no point to what we do on our scale, and given free fuel ...
I must make an aluminum flange to continue my new burner ...
So I made the small forge, as its Sunday I could make the play
I met him with a gas cylinder and an inner casing divided by concrete. Her keep the heat and allow better heat the aluminum.
You crucibles, you told me? It is great how?
Otherwise, you see, I did everything according to "my green colors"
It is not beautiful?
lot of work
I remain convinced that the resonance is no point to what we do on our scale, and given free fuel ...
I must make an aluminum flange to continue my new burner ...
So I made the small forge, as its Sunday I could make the play
I met him with a gas cylinder and an inner casing divided by concrete. Her keep the heat and allow better heat the aluminum.
You crucibles, you told me? It is great how?
Otherwise, you see, I did everything according to "my green colors"
It is not beautiful?
0 x
Manoria 68, fried researcher, technician of its oil mill
-
- Similar topics
- Replies
- views
- Last message
-
- 37 Replies
- 52280 views
-
Last message by BP86
View the latest post
27/10/19, 13:10A subject posted in the forum : Your technical assemblies, DIY, innovations and self-construction: making an object or an installation
-
- 160 Replies
- 205461 views
-
Last message by BP86
View the latest post
12/12/17, 15:57A subject posted in the forum : Your technical assemblies, DIY, innovations and self-construction: making an object or an installation
Who is online ?
Users browsing this forum : No registered users and 94 guests