Me I work "that" on diesel (almost !!!) I finished some proto and gasoline, it can interest me! And I'm a welder and I have what is needed or almost!
Side installation is not the easiest, but not impossible!
the beginning of the exhaust line, connect to the collector, is almost under the car, there is better a bridge to work!
It can be very interesting to equip a gasoline, (+ an 21)
We would be quickly fixed on certain parameters!
And it also depends on what type of bubbler you want to install!
And also and finally you will have a certain length of connection
between the reactor and the air intake!
It moves in the Loire :)
- Asgard bone tyr
- My R21 Pantone on TF1 :)
- posts: 160
- Registration: 06/02/05, 18:21
- Location: all over
- x 1
Thanks asgard,
I can see that the start of the exhaust dips quickly under the body; there is a curve. Does the reactor have to be straight (right if you want) or can it fit the curvature of the pipe?
I looked at your pantone system plan that you showed TF1, there is just one detail that I do not understand is the arrival of air that enters the bubbler, where the air comes from, does it pass through a filter?
Did you modify the exhaust pipe to leave a large exhaust gas passage once the reactor was in place, or did you keep the existing pipe welded inside your reactor? ?
How is your exit from the bubbler and your entry into the admission ?.
You've probably answered these questions but I can not see exactly how it works .... the exhaust gases only serve to heat the reactor?
How do you cause bubbles in the bubbler?
I am a beginner and I try to understand, it would be perfect if I had a montage "in real" under the eyes.
I suppose that if you make pollution measurements, is it that you have a control bench in a garage or a technical control center?
If you prefer you can answer me in private message, to you to see.
A +.
I can see that the start of the exhaust dips quickly under the body; there is a curve. Does the reactor have to be straight (right if you want) or can it fit the curvature of the pipe?
I looked at your pantone system plan that you showed TF1, there is just one detail that I do not understand is the arrival of air that enters the bubbler, where the air comes from, does it pass through a filter?
Did you modify the exhaust pipe to leave a large exhaust gas passage once the reactor was in place, or did you keep the existing pipe welded inside your reactor? ?
How is your exit from the bubbler and your entry into the admission ?.
You've probably answered these questions but I can not see exactly how it works .... the exhaust gases only serve to heat the reactor?
How do you cause bubbles in the bubbler?
I am a beginner and I try to understand, it would be perfect if I had a montage "in real" under the eyes.
I suppose that if you make pollution measurements, is it that you have a control bench in a garage or a technical control center?
If you prefer you can answer me in private message, to you to see.
A +.
0 x
Only when he has brought down the last tree, the last river contaminated, the last fish caught that man will realize that money is not edible (Indian MOHAWK).
- Asgard bone tyr
- My R21 Pantone on TF1 :)
- posts: 160
- Registration: 06/02/05, 18:21
- Location: all over
- x 1
-
- I discovered econologic
- posts: 4
- Registration: 04/03/09, 23:07
-
- Econologue expert
- posts: 4075
- Registration: 12/01/07, 08:18
- x 4
- Asgard bone tyr
- My R21 Pantone on TF1 :)
- posts: 160
- Registration: 06/02/05, 18:21
- Location: all over
- x 1
I do not know if it moves in the Loire, in any case it moves on the side of my home! I took a little late with my workshop because I have not had too much support. As I said in other page I remain available if some want this launch!
I propose weekend or day at home or otherwise I can move home. It's been a long time since I wait for a migration of pantonist-econologist to my home (or the opposite)! I meet more profiteer than sharer (and I remain courteous) but I remain available for those who really want to do something.
Looking forward to meeting those who are interested ... I go back to my workshop ... A +
I propose weekend or day at home or otherwise I can move home. It's been a long time since I wait for a migration of pantonist-econologist to my home (or the opposite)! I meet more profiteer than sharer (and I remain courteous) but I remain available for those who really want to do something.
Looking forward to meeting those who are interested ... I go back to my workshop ... A +
0 x
-
- Econologue expert
- posts: 4075
- Registration: 12/01/07, 08:18
- x 4
- Asgard bone tyr
- My R21 Pantone on TF1 :)
- posts: 160
- Registration: 06/02/05, 18:21
- Location: all over
- x 1
-
- Econologue expert
- posts: 4075
- Registration: 12/01/07, 08:18
- x 4
Back to "Water injection in the engines: the assembly and experimentation"
Who is online ?
Users browsing this forum : No registered users and 148 guests