Photos ökofen pellet boiler: installation and storage

[Christophe]

Hi Nebu and welcome to econo!

I did not expect to find a forum French also active on this brand.

Well, we're not unemployed!
But did you see this?, here is the most "complete" question ökofen boiler settings !

I believe that even ökofen France is interested in this work!

[Did67]

Hello Nachbar!!!

Did you see that there is a forum on the operation of Okofen, settings, etc. ???? Over 60 pages!

Right here : https://www.econologie.com/forums/suivi-du-t ... t6424.html

[Christophe]

Damn I did not find the right subject! Thank you did67 this was the one I was thinking of when talking about ökofen France ... who was it who contacted them again? You or dirk or ??

[Did67]

I wonder if they haven't landed themselves on the wire ???

And then, after an email full of goodwill, we hadn't seen them again and I had turned them on nasty with an "Okofen kill me!" which made them react. Response on forum? MP as far as I am concerned ...

Since then, we have been in contact, and they have always tried to find solutions to the cases described (individual contact with forumors with problems).

[Nebukadnezar]

Congratulations, I'm really impressed, plus everyone is friendly and helping each other, on German sites there are always idiots who believe they know everything better than the others and break up discussions instead of enriching them. So far I have not yet found a comparable site in Teutony.

So I'm going to start reading these threads that really look tip top.

By skimming over the discussions a little, Did67 states that I own the installer manual, I have several manuals, all in German of course, including a document printed in yellow "Montage und Installationsanleitung für den Installer", to Didier, I suppose it is this document you're talking about?

Then the installer code, is it the same for all installations?

What interests me is to be able to save the data on a USB stick, it is described in chapter 17 of the Pelletronic Plus manual. Do you need this code to activate the USB function?

Currently, at the end of the day, I write this data down manually in an Excel file.

Thank you

nebu

[Christophe]

Congratulations, I'm really impressed, plus everyone is friendly and helping each other, on German sites there are always idiots who think they know everything better than others and break up discussions instead of enriching them.

Uh objection .... no nothing !!

[kitikoi]

Hello everyone,

once is not custom, my first post on this forum is not a question, but an answer
New buyer of an okofen boiler, I have traveled a lot forum to try to understand how my new toy works. I understood the difference between the automat and the regul, but I still have a little trouble with the water law, but it will come ...
short to better target the operation of the automat, I put a compact flash to save the parameters, and I wanted at the same time to save the parameters of the regul on a USB key, but curiously I had not found the answer on the forum : it interests few people, or this regul is quite recent and few people have it?

still it is that google is my friend, and the 4 digit access code consists of the first 2 digits = the time and the last 2 = today's date. For the configuration of the recording, it is in the doc.

In attachment an example of what we harvest. I expected a little more info, and I don't understand all the columns either (those with header marked [ï¾ ° C] in particular):

https://www.econologie.info/share/partag ... GnrINZ.xls

have a good day

[Did67]

By skimming over the discussions a little, Did67 states that I own the installer manual, I have several manuals, all in German of course, including a document printed in yellow "Montage und Installationsanleitung für den Installer", to Didier, I suppose it is this document you're talking about?

Then the installer code, is it the same for all installations?

What interests me is to be able to save the data on a USB stick, it is described in chapter 17 of the Pelletronic Plus manual. Do you need this code to activate the USB function?

nebu

Oops, I had lost sight of this thread!

1) Yes, it is this document. Normally, it is not intended for the user. But it is provided, as the name suggests, to each installer. Who often (but not always) leave it ... There is information in there that is not in the guides for users.

2) The "installer code" on the boiler ("pellet control") to my knowledge has the same key on all Okofen. It allows you to go to the parameters of rank 2 on the boiler board. For example to change the nominal temperature (the one towards which the boiler "tends"; P 263 from memory, 70 ° C from factory, which I have reduced to 67 ° C). Or view a whole series of recording times (P24X series): screw, burner, apsirator, ignition, silo screw ... etc ...

3) I don't have the white regul: joker. No possibility to record on USB at home. The boiler plate can be saved on CompactFlash (but I did not succeed! A history of formatting)

[Did67]

but oddly enough I hadn't found the answer on the forum : it interests few people, or this regul is quite recent and few people have it?

It is fairly recent. Some old pillars of these forums (Dirk, me) still have the old TEM (so called "gray"). Did you put your request on the longest thread (operation of the Okofen regulation - more than 70 pages). Some have ...

[kitikoi]

while looking for the codes for the regul, I had seen this post. As nobody seemed to have the answer, I put the codes that I found.
I have not yet asked a question on the longest thread, I am waiting to have read all the posts relating to this, to ask relevant questions. Nothing annoys more than answering someone who hasn't bothered to potash

but promised i will find things to ask