Paper briquettes

crude vegetable oil, diester, bio-ethanol or other biofuels, or fuel of vegetable origin ...
Corpse Grinder 666
I understand econologic
I understand econologic
posts: 148
Registration: 17/11/08, 11:54




by Corpse Grinder 666 » 17/07/09, 21:50

to make: no thank you!
I renovated a shed, a permaculture to set up a bike lying to finish, and a stove can be manufactured, so I do not want to overload me.

Speed ​​is not a problem on when you are in mass stove for example (this is not my case);)
0 x
User avatar
jlt22
Éconologue good!
Éconologue good!
posts: 414
Registration: 04/04/09, 13:37
Location: Guingamp 69 years




by jlt22 » 17/07/09, 23:11

Corpse Grinder 666 wrote:a bike lying to finish)


Is a recumbent bike cooler than a normal bike for a walk?
0 x
User avatar
Cuicui
Econologue expert
Econologue expert
posts: 3547
Registration: 26/04/05, 10:14
x 6




by Cuicui » 17/07/09, 23:16

jlt22 wrote:
Corpse Grinder 666 wrote:a bike lying to finish)

Is a recumbent bike cooler than a normal bike for a walk?

According to a proverb from ancient Greece (I can't remember the exact reference): "we are better sitting than standing, and we are better lying than sitting".
0 x
User avatar
jlt22
Éconologue good!
Éconologue good!
posts: 414
Registration: 04/04/09, 13:37
Location: Guingamp 69 years




by jlt22 » 17/07/09, 23:25

Cuicui wrote: "we are better seated than standing, and we are better lying than seated".


Thank you, not need the proverb for noticing
0 x
User avatar
I Citro
Econologue expert
Econologue expert
posts: 5129
Registration: 08/03/06, 13:26
Location: Bordeaux
x 11




by I Citro » 18/07/09, 11:05

jlt22 wrote:The baler should have 10 kg / cm200, but brought back to the surface of the 2x30 briquette, it would have to be calculated.
Let's see that;
- If the piston the cylinder (not the barrel) is 10cm, with Pi x R² = 78, ... cm²
- If the hydraulic fluid is 200kg / cm² (200bar) pushes the jack 78x200 = 15707kg or 15 Tonnes.

If the press is either 30x30cm 900cm² then:
15707 / 900 17.45 = kg / cm² ...

Was it enough. :?:

Pellet presses produce pellets of 8mm with a pressure greater than 150 bar.
0 x
User avatar
I Citro
Econologue expert
Econologue expert
posts: 5129
Registration: 08/03/06, 13:26
Location: Bordeaux
x 11




by I Citro » 18/07/09, 11:51

jlt22 wrote:
Corpse Grinder 666 wrote:a bike lying to finish)
Is a recumbent bike cooler than a normal bike for a walk?
I also have a recumbent bike to finish.
Image
It has not changed much since that photo ...

For comfort, it depends on the chosen architecture.
It has nothing to do with a bike right, all the pins are shattered.
It's a bit like learning to ride a bike ...
0 x
azerty
I learn econologic
I learn econologic
posts: 23
Registration: 15/09/05, 13:44




by azerty » 18/07/09, 13:44

your recumbent bike is fine. how has you bent the main tube?
I tried to draw several shots based on 2x26 "+ recuperating frames, but each time the steering was too close to the pilot's testicles.
0 x
the middle
Econologue expert
Econologue expert
posts: 4075
Registration: 12/01/07, 08:18
x 4




by the middle » 18/07/09, 15:09

but each time the direction is too ready to see against the testicles of the pilot.

Must be cut! Image
Sorry, I could help but po ...
0 x
Man is by nature a political animal (Aristotle)
User avatar
I Citro
Econologue expert
Econologue expert
posts: 5129
Registration: 08/03/06, 13:26
Location: Bordeaux
x 11




by I Citro » 19/07/09, 21:02

azerty wrote:your recumbent bike is fine. how has you bent the main tube?
A connoisseur. :?
It was a hassle ... But it is not I who bowed. :? He is far from perfect. :|
azerty wrote:I tried to draw several shots based on 2x26 "+ recuperating frames, but each time the steering was too close to the pilot's testicles.
Well after trying different models, I decided that nothing suited me and that the ideal would be a 2x24 ".
I recovered a 24 "mountain bike fully suspended from the landfill and then drew my first templates on cardboard at scale 1.
Nevertheless a lot of trial and error. Here I think again the anchor of the damper on the swingarm (the down) to find the intended rake angle.
It will also modify some parameters of the seat and better.
0 x
User avatar
jlt22
Éconologue good!
Éconologue good!
posts: 414
Registration: 04/04/09, 13:37
Location: Guingamp 69 years




by jlt22 » 19/07/09, 22:31

citro wrote:
If the press is either 30x30cm 900cm² then:
15707 / 900 17.45 = kg / cm² ...
Was it enough. :?:


The product obtained seemed compact and I did not look at the problem at the time, my biggest concern was to reduce paper waste because we were clearly above our competitors. A press is first designed for print with a minimum
I doubt get a better result with Gadjets trade
0 x

 


  • Similar topics
    Replies
    views
    Last message

Back to "biofuels, biofuels, biofuels, BtL, non-fossil alternative fuels ..."

Who is online ?

Users browsing this forum : No registered users and 119 guests